Seal Rings Dealers in Bhayandar, Thane

We, at sam engineers are engaged in manufacturing, exporting and supplying v ring seals. The v ring seals, also called as axial shaft seals, are manufactured as per the set industrial standards using well-tested material. The clients can avail the v ring seals from us in varied specifications as per the requirement at affordable price. v ring seals types all rubber v ring are known as v ring sealsmetal cased v ring seals parts of v ring seals the v-seal is comprised of three basic parts. The body of the seal holds it into place on the shaft or mounting surface. The cone shaped flexible lip rides in light contact with the counter surface and does the sealing. The resilient hinge joins the other two parts together and provides the force which keeps the lip against the counter surface. It is these three parts, working together, which allows simple one piece seal to do what no other seal system can do. installations the v-seal can be completely assembled without the need of tools. Being all rubber, it can stretch up to 250% of its molded i.d., so it can be easily stretched over flanges, collars, and entire bearing housings during assembly. This same resilience holds the seal in place without the need for springs or clamps. To assemble the seal, it is stretched onto the shaft by hand and then pushed up against the counter face to a pre-determined width. seal function one v-seal functions as three different seals. The simple v-seal lip keeps dirt and water out, grease in and acts as a slinger. The v-seal can be used alone to seal lubrication in and/or contamination out, or it can supplement an oil seal, mechanical seal or labyrinth, keeping contamination away from the primary seal. speed in most applications, the v-seal rotates with the shaft to provide a slinging action. As such, it is subject to centrifugal force. At speeds below 1600 surface feet per minute (fpm), the stretch tension of the v-seal is sufficient to hold it onto the shaft.above 1600 fpm, axial back up is required in the form of a step in the shaft or a snap-ring or lock collarabove 2400 fpm, radial back up is required in the form of a mounting pocket or clamp around the v-seal body. Above 3000 fpm, the lip of the v-seal lifts away from the counterface resulting in a clearance seal and eliminating drag and wear. The v-seal can also be mounted stationary and run against a rotating counterface. In this case, centrifugal force has no effect on the v-seal the v-seal should always have axial back up in oil applications the basic dimensions of the v-seals are as follows: (i.e for a v-25 a). d – the molded inside diameter of the v seal =0.87”d1 - the shaft range the v-seal is made to fit = .095-1.07d2 - the maximum i.d. Of the counterface = d1 + 0.08d3 - the minimum o.d. Of the counterface = d1 + 0.45a - i.d. Width of the v-seal = .018b - o.d. Width of the v-seal = 0.3c - v-seal cross section = 0.1 b1 – v-seal fitted width = 0.24+/-0.03 materials the v-seal is available in a variety of different rubber materials for various operating conditions. Nitrile, neoprene, hnbr, epdm and silicone v-seals can all be supplied. Our proprietary anti-friction treatment (aft) reduces the already low friction of the v-seal even further. food grade materials are available including fda and nsf approved rubbers. In addition, our compounding lab can develop specialty materials for particular applications. For additional information, see our materials section or contact our technical department. for more details on sizes available, elastomer suitability or for any further queries.

Chevron packing seals also known as V packing seals are highly adaptive sealing products of standard rubber that comprises of rings of multiple “V” shaped lip seals that have been stacked vertically between reinforced header and compression ring to form a complete packing assembly. They are assembled with a reinforced backing ring to assist with extrusion resistance and with a compression ring that is used to impart axial squeeze on the chevron packing thereby imposing a transverse strain and energizing the packing. One important benefit of the vee packing is that it can operate under any mechanical situations. “V” shaped rings can be one or more as per requirement. These V shaped intermediate rings are tapered to snap-fit the housing during installation, thus they provide a good seal even at low pressures. Operating Capabilities They can operate at a pressure up to 5000 psi (344.737) bars. The operating temperature is in the range of 30 to 150 degree Celsius. The temperature working conditions completely depend on the material used when manufacturing the vee packing. Reciprocating speed is up to 0.5 meter per second.

• Brand Name: ALT-D-RON
• Application: Airless Painting Machine
• Material: PTFE
• Thickness: 5 mm
• Mount Type: Side & Top
• Quantity Per Pack: 6 Piece
• Model Name/Number: APSS04

rubber v ring, Plastic Fiber Fluorinated Polymer

diaphragms chevron packing, O-Ring, ptfe item, Gaskets

Silicone Lip Sealing Ring, Single Jet Flow Seal, silicone profile