TSV ENTERPRISES Anand Nagar, Thane, Maharashtra

TSV Enterprises is considered valuable market name for supplying Wall Mounting Enclosures which comes in Type ch in cast iron enclosures. 63 to 315a, 415 vac and type chd in sheet steel enclosures. 400to800a, 415 vac with 3 pole & 4 pole versions refis 13947-3-1993.These swith / switch fuse units are in sheet steel enclosures and available in type lp type wms 32 a 63 a, 415 vac, tp & n. 20a32a&63a, 415vac. Tp&n. These are use as sm fuse holders and can as are use safe clip fuse holders. The units have sude operating handles and front operating handles. This is on ac 23 category of duty. Isolator version is also available.

Porcelain Base Fuse Holder manufactured by TSV Enterprises is considered best in International market. The fuse Holders are manufacture from Porcelain. These are noninflammable, Non-hugroscopic and with good finish. Contacts Current carrying parts of the holders are made for precisely pressed copper/brass material and have extruded brass base ensure perfect alignment. Back up pressure clips have been precisely formed from Phosphor Bronze/Spring Steel material to ensure perfect mating of male and female parts, for long life. Terminals Adequate, full rated Copper/Brass terminals to suit direct cable termination in case of enclosed type Fuse. Holders and through Cable lugs for open type Fuse Carriers and are supplied complete with Cable holding fasteners. Silver plated contacts are the current carrying parts are heavily electroplated with silver to ensure long life, non-deteriorating contact surface for high efficiency mating.

We bring forth high quality LT ACB Feeder Pillar that is designed for providing higher safety, protection with reliability. It is an outdoor type 6 way l. T. distribution pillar with 800 amps suitable for 3 phase 50 hz. 440v AC system. We use the finest quality steel sheet of 14 swg and dust water which is vermin proof with well ventilated. Specifications : The bottom pedestal of pillar provided with 50x50x6 M. S. angles to give solid strength to the pillar boxes. Spray painting and oven backing after seven tank process for better finish and long life of paintingHeavy duty hinges with brass insert to give smooth operation of door & safety from corrosion6 mm thick asbestos sheet lining provided in inner side of door & inside the pillar compartment, & separation between cable connection and incoming for protection of current. Electrolytic grade copper bus bar of 40x5mm size to carry designed current inserted with heat shrinkable sleeves for safe operationE.S. GRADE Aluminum bus bar of 50*10mm size to carry designed current inserted with heat shrinkable sleeves for safe operation2 nos of earthing terminals facilitating better earthing of pillar boxesDetachable type bottom gland plate with suitable gland of cable sizePorcelain base fuse holders with silver plated, copper contacts of suitable rating. Door operated illuminating lamp for maintenance purpose. Embossed name plate, lot no & date of manufacturing provided as per requirement of buyer

TSV Enterprises holds specialization when it comes to the manufacturing of finest Dbs Busbar System. Our Dbs Busbar System can be used with single phase or three phase busbar as 4/6/8/12 way db. Three phase busbar can also be used for applications such as One row for powerOne row for lighting We also provide four separate sections; each having three phase distributors for various sections of the house is also possible. Our Dbs Busbar is available with double door and double door can also be replace existing cover at site.

TSV Enterprises are the leader in manufacturing of Capacitor Control Panel, which are provided for controlling the power factor of the complete installation. The front ccp houses fully compartmentalized feeders for controlling individual capacitors, where as rear side of the tc type ccp houses capacitors in well ventilated panel area. Capacitor Control Panel, we manufacture are of high quality and are made up of best raw material. We hold an international market value when it comes to the Capacitor Control Panel we supply.

We are reckoned as one of the prominent Tubular Aluminum Lugs Manufacturers in India. The materials we used in the manufacturing of the Aluminum Lugs ensure high durability, tensile strength and high conductivity. The unmatched quality and unsurpassable performance has attracted various industrial sectors to place repeated orders for the Aluminum Ground Lugs. Aluminum Lugs. Additionally, customers are eased with the availability of the Copper Aluminum Lugs in sizes mentioned as per the IS Specifications.

Finishing : Non Coated

Color : Shiny-Silver

Condition : New

Application : Electrical Ue

Size : 1.1/2inch

Certification : ISO 9001:2008 Certified

Grade : AISI

Feature : Non Breakable

Pattern : Plain

Type : Aluminium Lugs

Country of Origin : India

We offer highly efficient 4 Way L T Feeder Pillar meticulously designed to provide higher safety, reliability and protection with due consideration of aesthetic features. It is an outdoor type 4way l. T. distribution pillar with 500 amps suitable for 3 phase 50 hz. 440v AC system. The Pillar is made of finest quality steel sheet of 14 SWG which is vermin proof and adequately ventilated. Specifications : Bottom pedestal of pillar provided with 50x50x6 m. S. Angles providing solid strength to the pillar boxes.Spray painting and oven backing after seven tank process for better finish and long life of painting. Heavy duty hinges with brass insert for the smooth operation of door & safety from corrosion. 6 mm thick asbestos sheet lining in inner side of door & inside the pillar compartment, & separation between cable connection and incoming for protection of currentElectrolytic grade copper bus bar of 40x5mm size to carry designed current inserted with heat shrinkable sleeves for safe operationE.S. GRADE Aluminum bus bar of 50*10mm size to carry designed current inserted with heat shrinkable sleeves for safe operation. 2 nos of earthing terminals provided to facilitating better earthing of pillar boxes. Detachable type bottom gland plate with suitable gland of cable sizePorcelain base fuse holders with silver plated, copper contacts of suitable rating. Door operated illuminating lamp provided for maintenance purpose. Embossed name plate, lot no & date of manufacturing provided as per requirement of buyer.

4 Way H.T. Feeder Pillar manufactured by TSV Enterprises provide higher safety, reliability and protection with due consideration of aesthetic. Way H.T. Feeder Pillar, we manufacture are suitable for 3 phase 50 hz 11 kv ac system and are made of finest quality of sheet steel of 3 mm thickness, water proof dust & vermin proof with adequately ventilated. Their main body frame made of 50x50x5 angle to give solid strength to feeder pillar & frame base made with 65x65x5 angle which under goes spray painting & oven baking after seven tank process for better finish and long life of painting and also through heavy duty hinges with brass insert to give smooth operation of door & safety from corrosion. A 3 mm thick Bakelite sheet lining is provided on inner side of body for protection of high current. An electrolytic grade copper bus bar of 50x6mm is provided to take designed current inserted with heat shrinkable sleeves for safe operation. We also provide two nos of copper earthing terminals to facilitating better earthing of pillar and detachable type bottom gland plate, with door for safety purpose. We also embossed name plate, lot no & date of manufacturing provided as per requirement of buyer.

TSV Enterprises provide reliable and protected 22 KV HT Feeder Pillar with due consideration of aesthetic which are suitable for 3 phase 50 hz 22 kv ac system. Our 22 KV HT Feeder Pillar is made up of finest quality of sheet steel of 3 mm thickness and under goes water proof dust & vermin proof with adequately ventilated. Main body frame we made are of 50 x 50 x 5 angle to give solid strength to feeder pillar & frame base made are with 65x65x5 angle.. Spray painting & oven baking is given after seven tank process for better finish and long life of painting. A brass insert to give smooth operation of door & safety from corrosion and 6 mm thick Bakelite sheet lining provided on inner side of body for protection of high current. An electrolytic grade copper bus bar of 50x6(double) provided to take designed current inserted with heat shrinkable sleeves for safe operation. We also deals in embossed name plate lot no & date of manufacturing provided as per requirement of buyer.

we are recognized as one of the stupendous distribution feeder pillar boxes suppliers in mumbai, india. The unmatched quality and unsurpassable performance has attracted various industrial sectors to place repeated orders for the feeder pillar boxes. the feeder pillar boxes, offered by us, are used to fit the electrical cutouts in almost every industry. It is safe and best way to put all electrical cutouts together. The company has also earned acknowledgment for providing 6 way feeder pillar boxes as per the is specifications. features :- shock proofeasily installedlow maintenanceaccurate functioning sizes available :- two waythree wayfour waysix way material used :-metal sheetaluminium copper bus barhrc fuse base, etc applications :- used for the transmission of current supply from transformer to the destination such as (meters, society, etc.)

We are listed at the apex in the list of the outstanding high rupture capacity fuse manufacturers in dombivali (e) thane, maharashtra. The use of optimum quality materials in the manufacturing of the hrc fuse ensures high durability, tensile strength and high conductivity. The unmatched quality and unsurpassable performance has attracted various industrial sectors to place repeated orders for the hrc fuse links. Additionally, we also specialize in providing hrc fuse as per the sizes mentioned by is specifications. Features :-high durabilitytensile strengthhigh conductivity sizes available:- available in various sizes from 20amp to 630amp. Raw material used :- insulated base and high conductivity connector of fuse. Applications :- group a:-close type fuse fittings are suitable for off-set tag fuses. 2032 amp. Fuse fitting are available with frontbus-bar and rear connection arrangement while 32 amp. & 100 amp. Rating are suitable for front and bus-bar connections. Ample contact area with non ferrous high pressure backing plates ensure low temperature rise. A minimum number of component have been used thus insuring simplicity of design and reliability in operation. Moulded components are manufactured from electrical grade of phenolic powder. An aperture has been provided on the top of the carrier of the quick indication of fuse operation without removing the carrier.group b:-snf 2032 amp. Safe clip type fuse fitting is design to accommodate with both bolted panel and a direct 35 mm din rail mounting. The product is suitable to the compact rant of off-set type blade tag fuse link. The product is very significant in saving of time and power loss. Easy removable of fuse carrier from the fuse base is possible with the help of a cam lock arrangement. Fabulous and unique looking carrier having cam locking arrangement without carrier contact provides very low wattage loss due to low contact resistance between the fuse link and base contact.group c :-open type fuse bases are available in 100 amp. 250 amp. 40 amp & 630 amp in this range. The moulded components are manufactured in phenolic compound as well as in dough moulded compound. Contacts are silver plated thus keep the contact resistance to the minimum. Lyre shape contact and spring loaded contact generate on the fuse blades resulting in very low temperature rise.

We are offering wall mount enclosure. Tsv enterprises is considered valuable market name for supplying wall mounting enclosures which comes in type ch in cast iron enclosures. 63 to 315a, 415 vac and type chd in sheet steel enclosures. 400to800a, 415 vac with 3 pole & 4 pole versions refis 13947-3-1993.these swith switch fuse units are in sheet steel enclosures and available in type lp type wms 32 a 63 a, 415 vac, tp & n. 20a32a&63a, 415vac. Tp&n. These are use as sm fuse holders and can as are use safe clip fuse holders. The units have sude operating handles and front operating handles. This is on ac 23 category of duty. Isolator version is also available.

We are offering 4 way h.t. Feeder pillar manufactured by tsv enterprises provide higher safety, reliability and protection with due consideration of aesthetic. Way h.t. Feeder pillar, we manufacture are suitable for 3 phase 50 hz 11 kv ac system and are made of finest quality of sheet steel of 3 mm thickness, water proof dust & vermin proof with adequately ventilated. Their main body frame made of 50x50x5 angle to give solid strength to feeder pillar & frame base made with 65x65x5 angle which under goes spray painting & oven baking after seven tank process for better finish and long life of painting and also through heavy duty hinges with brass insert to give smooth operation of door & safety from corrosion. A 3 mm thick bakelite sheet lining is provided on inner side of body for protection of high current. An electrolytic grade copper bus bar of 50x6mm is provided to take designed current inserted with heat shrinkable sleeves for safe operation. We also provide two nos of copper earthing terminals to facilitating better earthing of pillar and detachable type bottom gland plate, with door for safety purpose. We also embossed name plate, lot no & date of manufacturing provided as per requirement of buyer.