Sawan Engineers Waghodia, Vadodara, Gujarat

zDesign: Split tee will be designed base on ANSI / ASME, with design factor 0.4, 0.5 and 0.72. All mechanical calculation for pressure parts under internal pressure or external forces and fabrication drawings which prepared base on Client’s Technical Specifications will be prepared and forwarded to client for approval. Split Tees are available in a broad range of material types and grades on size and reduced branch outlets Split Tee Fittings available designed in accordance with ANSI / ASME B31.8 , B31.1 , B31Split tee will be designed base on ANSI / ASME, with design factor 0.4, 0.5 and 0.72. All mechanical calculation for pressure parts under internal pressure or external forces and fabrication drawings which prepared base on Client’s Technical Specifications will be prepared and forwarded to client for approval. Split Tees are available in a broad range of material types and grades on size and reduced branch outlets Split Tee Fittings available designed in accordance with ANSI / ASME B31.8 , B31.1 , B31.3, and B31.4 Hot Tap Split Tees are available for pipe sizes from 2” – 48” and are available in ANSI class 150 to ANSI class 2500. FEATURE CODE :  Compatible with existing hot tapping/plugging equipment  Can be utilized for either hot tapping or line stopping  Split tee fittings eliminate alignment problems  There is no potential for weld to penetrate the tapping area  Allows for maximum hot tap size  Size-on-size fittings normally are available off-the-shelf  Full range of reducing branch sizes available  Greater wall thickness  Higher allowable stresses  More reinforcement area  Design: ANSI B31.1, B31.3, ANSI B31.4 & B31.8 ASME Sec. VIII Div.1 & 2  Fabrication: ASME Sec. VIII Div.1    Welding: ASME Sec. IX • NDT : ASME Sec. V.3, and B31.4 Hot Tap Split Tees are available for pipe sizes from 2” – 48” and are available in ANSI class 150 to ANSI class 2500. FEATURE CODE :  Compatible with existing hot tapping/plugging equipment  Can be utilized for either hot tapping or line stopping  Split tee fittings eliminate alignment problems  There is no potential for weld to penetrate the tapping area  Allows for maximum hot tap size  Size-on-size fittings normally are available off-the-shelf  Full range of reducing branch sizes available  Greater wall thickness  Higher allowable stresses  More reinforcement area  Design: ANSI B31.1, B31.3, ANSI B31.4 & B31.8 ASME Sec. VIII Div.1 & 2  Fabrication: ASME Sec. VIII Div.1  Welding: ASME Sec. IX • NDT : ASME Sec. V

Barred tees are used in a pig launcher receiver system and or at branches in the pipeline to ensure the safe passage of a pig or sphere past the open branch area. To complement our range of pigs and spheres pipeline engineering has the in-house engineering, manufacturing and testing capacity to produce piggable pipeline barred tees. Piggable barred tees incorporate simple bar sections welded across the pipeline tee branch to allow a pig to negotiate the branch opening. Piggable tees are manufactured to specific customer project specifications and International pressure vessel and piping codes such as ASME, PD5500.

SAWAN’s vastly experienced team of engineers, operators & managers take utmost care to ensure the highest quality of pipe bends consistently, in strict adherence & conformance to the international specifications.  API – 5L  MSS – SP – 75  ASME – B – 31.1  ASME – B – 31.3  ASME – B – 31.4  ANSI – B – 16.9  ASTM – A – 234  PFI – ES – 24  ISO – 15590 – 1  DNV – 2000  EIL Specifications SAWAN’s strong emphasis on using best raw materials & controlling process parameters results in production of mechanically sound & dimensionally accurate bends with high degree of repeatability leading to output yield maximization. The in – house multiple quality checks & tests guarantee shipments of 100% defects less materials to customers’ sites. Each & every bend is ‘Pig’ tested to avoid any hassles after installation. SAWAN also has an in – house hydro testing facility for bends which can be undertaken based on customers’ requirements. Range of Bend :1/2" to 48" Radius :Up to 21D Schedual / thickness :Up to 60mm Material of Construction in Bends:CS/LTCS/HYCS/AS/SS/DSS

The SAWAN’s Flow Tee is a specialized fitting that facilitates the passage of pipeline pigs past tee connections – where flow bypass often leaves pigs stranded without restricting product flow. The FLOW TEE is effective even for full-diameter branch openings. The key to the FLOW TEE is its radial flow design, which provides an inner sleeve to direct the pig through the primary line, past the branch. Flow holes in the sleeve and the annular cavity provide a flow area at least equal to the flow area of the branch line, permitting full product flow through the tee during normal operations. Flow Tees can be supplied for all pipeline sizes, with any size of reducing branch, and to meet any ANSI rating or have the same pressure rating as the host pipeline. FLOW TEE can also be provided with flanged end connections.

flange type: welding neck , long welding neck, lap joint, blind, slip-on, threaded, reducer, socket welding,orifice, spectacle blind   specifications: ansi b16.5, ansi b 16.47, ansi b16.36, ansi b16.48, mss sp44, api 590, api 6a, bs series, en 1092, uni series, din series . material: astm a105; astm a350 lf1,lf2 cl1/cl2, lf3 cl1/cl2; astm a694 f42, f46, f52, f56, f60, f65, f70 astm a182 f304/304l, f316/316l, f316h, f310, f312 astm a182 f1, f5a, f9, f11, f12, f22, f91 astm a182 f51/uns s31803, f53/uns s32750, f55/uns s32760 face type: flat face, raised face, ring joint face, lap-joint face,large male-female, small male-female,large tongue & groove, small tongue & groove size: 1/2" --- 60".

RANGE, SCHEDULES & TYPES Range of Butt weld fittings : 1/8” To 26" Seamless & 8" To 96" Welded Schedules of Butt weld fittings : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS with NACE Certifications Types of Butt weld fittings : Elbow/Tee/Reducer/Cap/Stub End/LATERAL TEE   Type Of Construction :Seamless,Welded & Fabricated   MATERIALS OF CONSTRUCTION IN BUTTWELD FITTINGS Stainless Steel Buttweld fittings : ASTM A403 WP Gr. 304, 304H, 304L, 309, 310, 316, 316L, 316TI, 316H, 317L, 321, 347, 904L Carbon Steel Buttweld fittings : ASTM A234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70 Low Temperature Carbon Steel Buttweld fittings : ASTM A420 WPL3 , A420WPL6 Alloy Steel Buttweld fittings : ASTM / ASME A/SA 234 Gr. WP 1, WP 5, WP 9, WP 11, WP 12, WP 22, WP 91 Duplex Steel Buttweld fittings : ASTM A 815, UNS NO S 31803, S 32205, S 32760, S 32750 Nickel Alloy Buttweld fittings : *Standards in Butt weld fittings

Barred tees are used in a pig launcher / receiver system and / or at branches in the pipeline to ensure the safe passage of a pig or sphere past the open branch area. To complement our range of pigs and spheres pipeline engineering has the in-house engineering, manufacturing and testing capacity to produce piggable pipeline barred tees. Piggable barred tees incorporate simple bar sections welded across the pipeline tee branch to allow a pig to negotiate the branch opening. Piggable tees are manufactured to specific customer project specifications and International pressure vessel and piping codes such as ASME, PD5500. Our capacity ranges from 2" to 72", ANSI Ratings 150 to 2500 and API, using carbon, stainless and alloy steel materials. Barred Tees can be supplied for all pipeline sizes, with any size of reducing branch, and to meet any ANSI rating or have the same pressure rating as the host pipeline. Barred Tees can also be provided with flanged end connections.   Dimensional Specification: ANSI B 16. 9 & MSS SP-75   Key Specifications/Special Features: Material: ASTM A 234 WPB, WPHY -42, WPHY 46, WPHY 52, WPHY 56, WPHY-60, WPHY-70 Wall Thickness: Sch 40- Sch 160   Applications:  Gas Gathering Systems  Mainline Pipeline  Oil & Gas Transmission Size: 2” TO 72” PRESSURE RATINGS : 150# TO 2500# MOC : CS/SS/AS/LTCS/DSS/HYCS