Siddhi Vinayak Engineers Gidc, Vapi, Gujarat

MOC : Copper Alloy (Gunmetal) / Alu. Alloy (Light Alloy)/Stainless SteelInlet : 63 mm size Male Instantaneous Inlet to Operate with Pressurized Water 100 mm Size Round Threaded (BSRT) Suction InletOutlet : 100 mm Size Round Threaded (BSRT)Finish : Painted Fire Red/ PO Red with Male Instantaneous Inlet Polished

An AC drive controls the application by continuously adjusting the motor speed. This results in reduced energy usage and prevents unnecessary wear of the equipment. CG offers a wide product range in the low voltage drives segment. Direct torque control and built-in shaft power monitoring are examples of premium features of AC drives.  

High dynamics for demanding applicationsEmotron VFX 2.0 AC drive optimizes the operation of your cranes, crushers, mills and mixers. Your process is protected from damage and downtime and you will benefit from reduced installation, energy and maintenance costs.

Material : Gun Metal LTB - II & Stainless SteelSize : 63 mm, 52 mm, 38 mm dia63 Female single outlet type - "A"63 Female double outlet type-"B"Performance Test : Hydraulic Test : 21 Kgf/cm2

Material : Gun Metal LTB - II & Stainless Steel

Track runner bearings are designed to run on all types of tracks and to be used in cam drives, conveyor systems, etc. These bearings have a thick-walled outer ring, which enables them to accommodate high radial loads, while reducing distortion and bending stresses.  

Detect hot spots before they cause troubleUsing an SKF Thermal Camera is a proactive way to help you detect problems before they occur, increasing uptime and improving safety. They allow you to be able to visualise potential problems, invisible to the naked eye, by presenting a picture of the heat distribution of an asset. The thermal image, presented on a large LCD screen, shows you where the temperature is either too hot or too cold allowing you to pinpoint potential problems fast.  

Taper roller bearings can take both axial and radial loads. The axial load carrying capacity of the bearings is largely determined by the contact angle α. If the contact angle α is larger, then the axial load carrying capacity is higher and vice versa.  

MOC : Gunmetal / Aluminum Alloy / Cast IronInlet/Outlet : Gunmetal / Aluminum AlloySizes : Inlet: 75mm (3") / 100mm (4") / 137mm (5½") Round ThreadedOutlet: 63mm (2 1/2") with NRV - 3 Nos. - Male Instanteneous typeTest Pressure : 21 kgf/cm²  

SKF Sprockets come in a wide range of sizes. With a comprehensive selection available, you will never have to worry about finding the perfect sprocket size for your application.  

Spherical roller bearings are self-aligning bearings designed for heavy radial loading. The rollers are barrel shaped. These bearings automatically compensate for large angular errors commonly called shaft misalignments. They are usually of double row design, both the rows of the rollers having common spherical raceways in the outer ring.  

BEARING UNITS & HOUSINGS SKF provides different types of bearing units that are ready-to-mount bearing units, which are greased and sealed, and are able to compensate for misalignment of the shaft with respect of the housing.    

SKF ball or roller thrust bearings are fitted with a form-stable cage to reliably retain and guide a large number of ball or rollers. The very small diameter deviation of the ball or roller within one assembly enables these bearings to accommodate heavy axial loads and shock loads.  

Tapered roller bearings have tapered inner and outer ring raceways and tapered rollers. They are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads. The projection lines of the raceways meet at a common point on the bearing axis to provide true rolling and low friction. The axial load carrying capacity of tapered roller bearings increases with increasing contact angle α. The size of the angle is related to the calculation factor e (→ product tables): the larger the value of e, the larger the contact angle. A single row tapered roller bearing is typically adjusted against a second tapered roller bearing.  

Spherical roller bearings have two rows of rollers, a common sphered outer ring raceway and two inner ring raceways inclined at an angle to the bearing axis. The centre point of the sphere in the outer ring raceway is at the bearing axis.  

SKF needle roller bearings are bearings with cylindrical rollers that are small in diameter relative to their length. The ends of the rollers are relieved slightly to modify the line contact between the rollers and raceways. This prevents stress peaks at the roller ends to extend bearing service life.  

SKF cylindrical roller bearings are available in many designs, series and sizes. The majority are single row bearings with a cage. High-capacity bearings, double row bearings, multi-row bearings, single, double and multi-row full complement bearings (without a cage) and split bearings complete the SKF standard assortment provided here.  

Angular contact ball bearings have raceways in the inner and outer rings that are displaced relative to each other in the direction of the bearing axis. This means that they are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads.  

Self-aligning ball bearings have two rows of balls and a common sphered raceway in the outer ring. The bearings are insensitive to angular misalignment of the shaft relative to the housing.  

Seals have a crucial impact on system performance. Life and reliability of what is often considered a simple component can make all the difference to your products and operations. SKF has more than 100 years of experience in various industries and applications, and is the only company that can support key aspects of the sealing system through its knowledge of bearings, seals, lubrication and associated science and technology.  

Belt performance is highly dependent on pulley performance. High quality pulleys can significantly increase belt life and reduce the total cost of ownership of your machinery.  

NBC has partnered with ConMet of USA to manufacture Pre-Set Hub assemblies for Heavy commercial vehicle applications. Preset hubs utilize pre-adjusted bearings to facilitate proper installation, extend seal and bearing life and ease maintenance. Almost 90% of the heavy trucks in North America use the preset hub technology. A preset hub is a pre-adjusted but serviceable assembly.  

Features Petra lift machine units of substantial construction combining rigidity and compactness in a single traction unit with monobloc gearbox casing that houses motor, brake, sheave pulley etc.